FEATURED · October 4, 2026
Hydraulic Hose Routing Around a Moving Cylinder
Plan cylinder hose length, bend radius, movement and protection before installation to reduce pressure loss and premature failure.
Read the Guide →NEWS & TECHNICAL INSIGHTS
Explore practical articles covering custom cylinder specification, hydraulic systems, manufacturing, fluid management, project preparation, and industrial applications.
October 4, 2026
Hydraulic Cylinder Rod Bushing Inspection Before a Seal Repair
A practical inspection sequence for the rod bushing, rod surface and seal grooves before replacing leaking cylinder seals.
Read more →
October 4, 2026
Hydraulic Cylinder Wear Rings: Why Seals Should Not Carry the Side Load
Understand the guiding role of piston and rod wear rings, how side load is transferred and what to check during cylinder repair.
Read more →
October 4, 2026
Piston Rod Coatings for Hydraulic Cylinders: A Buyer’s Comparison Framework
Compare rod coatings by corrosion, wear, seal compatibility and repair requirements for demanding hydraulic-cylinder duty.
Read more →
October 4, 2026
Tie-Rod vs Welded Hydraulic Cylinders: How to Specify the Construction
Compare tie-rod and welded hydraulic-cylinder constructions by installation envelope, service approach, mounting and duty.
Read more →
September 28, 2026
Hydraulic Pump Cavitation: Check the Suction Side Before Replacing the Pump
A practical guide to diagnosing low inlet pressure, restrictive suction lines, cold oil and other conditions linked to hydraulic pump cavitation.
Read more →
September 28, 2026
Hydraulic Accumulator Selection: Usable Oil Volume, Precharge and Temperature
Understand the input data needed to size a hydraulic accumulator, including usable fluid volume, pressure range, gas precharge and temperature.
Read more →
September 28, 2026
Hydraulic Cylinder Seal Material Selection: Fluid, Temperature and Duty
Specify hydraulic cylinder seals by fluid compatibility, operating temperature, pressure, motion and contamination rather than material name alone.
Read more →
September 28, 2026
Counterbalance Valves for Hydraulic Cylinders: Holding and Controlling an Overrunning Load
Learn when a counterbalance valve helps hold a hydraulic cylinder load, control lowering and reduce overrunning motion.
Read more →
September 28, 2026
Telescopic Hydraulic Cylinders: Stages, Force and Stroke Selection
Understand how telescopic cylinder stages affect collapsed length, extension force, speed and the choice between single- and double-acting designs.
Read more →
September 27, 2026
Hydraulic Cylinder Regenerative Circuits: Faster Extension and the Force Trade-Off
Understand how rod-side oil can be redirected to the cap side for faster extension and why available extension force changes.
Read more →
September 27, 2026
Hydraulic Power Unit Cooling: Estimate Heat Load Before Choosing a Cooler
Estimate hydraulic heat generation and compare air-oil versus water-oil cooling using the real duty cycle and site conditions.
Read more →
September 27, 2026
How to Store a Hydraulic Cylinder Before Installation
Protect a spare or project hydraulic cylinder from moisture, contamination and rod damage before commissioning.
Read more →
September 27, 2026
Hydraulic Cylinder Port Sizing: Flow, Pressure Drop and Connection Details
Learn why cylinder port selection must consider cap-side and rod-side flow, pressure loss, hose layout and end cushioning.
Read more →
September 27, 2026
Hydraulic Cylinder Position Feedback: Choosing a Sensor for Closed-Loop Control
Compare internal magnetostrictive sensors, LVDTs and external position measurement when specifying a closed-loop hydraulic cylinder.
Read more →
September 24, 2026
How to Synchronize Two Hydraulic Cylinders Without Assuming Equal Flow Is Enough
Compare mechanical coupling, flow dividers and position feedback when two hydraulic cylinders must lift or move together.
Read more →
September 24, 2026
Hydraulic Oil Cleanliness Codes and Filter Selection Explained
Understand ISO 4406 oil cleanliness codes, target selection, filter efficiency and sampling practices for hydraulic systems.
Read more →
September 24, 2026
How to Size a Hydraulic Power Unit from the Machine Duty Cycle
Build a pressure-flow duty cycle before selecting a hydraulic power unit, pump, motor, reservoir and cooler for a custom machine.
Read more →
September 24, 2026
Hydraulic Cylinder Factory Acceptance Testing: What Buyers Should Specify
A practical hydraulic cylinder FAT checklist covering dimensions, function, proof pressure, leakage, documentation and agreed acceptance criteria.
Read more →
September 24, 2026
Hydraulic Cylinder Mounting Styles: Clevis, Flange, Trunnion and Foot Mounts
Compare clevis, flange, trunnion and foot-mounted hydraulic cylinders by motion path, force direction, alignment and structural support.
Read more →Have a Topic or Project Question?
Contact our engineering team for technical clarification related to hydraulic cylinders, systems, steel structures, testing, or project delivery.